ACIM Personal Knowledgebase

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== KVM bridged networking ======


By default dhcpd based network bridge configured by libvirtd. You can verify that with the following commands:
<code bash>
# brctl show
# virsh net-list
</code>

KVM default networking
All VMs (guest machine) only have network access to other VMs on the same server. A private network 192.168.122.0/24 created for you. Verify it:
<code bash>
# virsh net-dumpxml default
</code>

If you want your VMs avilable to other servers on your LAN, setup a a network bridge on the server that connected to the your LAN. 

===== Bridge with NetworkManager and DHCP =====

Update your nic config file such as ifcfg-enp3s0 or em1:
# vi /etc/sysconfig/network-scripts/enp3s0

Add line:

<code bash>
BRIDGE=br0
</code>
Save and close the file in vi. Edit /etc/sysconfig/network-scripts/ifcfg-br0 and add:
<code bash>
# vi /etc/sysconfig/network-scripts/ifcfg-br0
</code>

Append the following:

<code bash>
DEVICE="br0"
# I am getting ip from DHCP server #
BOOTPROTO="dhcp"
IPV6INIT="yes"
IPV6_AUTOCONF="yes"
ONBOOT="yes"
TYPE="Bridge"
DELAY="0"
</code>
Restart the networking service (warning ssh command will disconnect, it is better to reboot the box):
<code winbatch>
# systemctl restart NetworkManager
</code>

Verify it with brctl command:
<code bash>
# brctl show
</code>

===== Manual Bridge with static IP  =====

By KVM Virtual Manager can be created bridge interface on each of network interface
{{ :linux:bridge_virt_01.jpg |}}

==== If you have two LAN interface with two VLAN network ====

<code bash>
[root@localhost ~]# cat /etc/sysconfig/network-scripts/ifcfg-br1
DEVICE="br1"
ONBOOT="yes"
TYPE="Bridge"
BOOTPROTO="none"
IPADDR="10.5.22.51"
NETMASK="255.255.255.0"
GATEWAY="10.5.22.254"
IPV6INIT="yes"
IPV6_AUTOCONF="yes"
DHCPV6C="no"
STP="on"
DELAY="0.0"
</code>
<code bash>
[root@localhost ~]# cat /etc/sysconfig/network-scripts/ifcfg-br2
DEVICE="br2"
ONBOOT="yes"
TYPE="Bridge"
BOOTPROTO="none"
IPADDR="10.5.23.10"
NETMASK="255.255.255.0"
IPV6INIT="yes"
IPV6_AUTOCONF="yes"
DHCPV6C="no"
STP="on"
DELAY="0.0"
</code>
<code bash>
[root@localhost ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth0
DEVICE=eth0
ONBOOT=yes
BRIDGE="br1"
</code>
<code bash>
[root@localhost ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth1
DEVICE=eth1
ONBOOT=yes
BRIDGE="br2"
</code>

<note warning>In this configuration second interface eth1 and br2 will not be accessible outside.</note>

<note important>To use a second interface and address we need to add another routing table.To do this go to file:</note>

<code bash>
# vim /etc/iproute2/rt_tables
</code>
and add at the end “1 rt2”:

<code winbatch>
#
# reserved values
#
255     local
254     main
253     default
0       unspec
#
# local
#
#1      inr.ruhep
1 rt2
</code>

Now we need to add routing rules and routes:

<code bash>
ip route add default via 10.5.23.254 dev br2 table rt2;
ip rule add from 10.5.23.0/24 table rt2
</code>

You can check these changes with commands:

<code bash>
# ip route show table rt2
# ip rule show
</code>

==== CentOS: Start custom script automatically after network startup ====

Find the ifup-post under /etc/sysconfig/network-scripts. This scipt is called right after any network interface is brought up online. In this script, you will find the following code snippet toward the end.
<code bash>

if [ -x /sbin/ifup-local ]; then
    /sbin/ifup-local ${DEVICE}
</code>

In the code snippet above, if ifup-local script exists in /sbin location, then script gets executed with an interface name in argument. Usually no such ecript like ifup-local exists so in order to run a startup script automatically after a network interface is up. Create an executable script called ifup-local in /sbin and put in there any command or script you wish to run.

Here is an example:

<code bash>
if [[ "$1" == "eth0" ]]
then
  echo "this part will be executed right after eth0 is up."
  echo "so you can put any startup command for eth0 here"
else
  #DO_NOTHING
fi
</code>

when script is done, use command to get the script executable.

<code bash>
$ sudo chmod +x /sbin/ifup-local
</code>


<code bash>
[root@localhost ~]# cat /sbin/ifup-local
#!/bin/sh

ip route add default via 10.5.23.254 dev br2 table rt2;
ip rule add from 10.5.23.0/24 table rt2
</code>
ACIM Personal Knowledgebase

User Tools

Site Tools

Page Tools
